Kodak 9090DC Manuale Utente

A-61662 October 2011 1-511 Exit tray — where document(s) are deposited after they have passed through the transport. There are two sets of slots tha

1-6 A-61662 October 2011 12 Document stop guide — adjust this guide to match the length of the documents being scanned, which aids in neat document

A-61662 October 2011 1-7Rear view1 Imprinter door — provides access to the optional imprinter for installation and maintenance. 2 Straight pass-thro

A-61662 October 2011 2-1 2 InstallationContents Installing the exit deflector ...2-1Insta

2-2 A-61662 October 2011 Installation: with a USB connectionIf you are using the optional SCSI connection, refer to the next section for installatio

A-61662 October 2011 2-3Installation: with an optional SCSI connectionThe Kodak Ngenuity Scanner is equipped to accommodate a SCSI connection for co

2-4 A-61662 October 2011 The Ngenuity Operator Utility Home Screen (default) will update when the scanner self tests have passed and communication w

A-61662 October 2011 3-13 Getting StartedContents Getting your scanner ready to scan...3-1Making scanne

3-2 A-61662 October 2011 Getting your documents ready to scanFor best scanning results, follow these guidelines:• Standard paper size documents fee

A-61662 October 2011 3-3Manually feeding documentsFor demonstration purposes, VRS Test Application is used in the following procedure.1. Turn on the

SafetyUser Precautions• Place the scanner on a sturdy, level work surface capable of supporting 50.8 kg (112 lbs) and leave adequate clearance on all

3-4 A-61662 October 2011 Accelerated scanning (VRS only)If you want to improve the scanning throughput at 300 dpi (or greater), you can change your

A-61662 October 2011 4-14 Control Panel and Ngenuity Operator UtilityContents Control panel...

4-2 A-61662 October 2011 Control panel The control panel is located on the front of the scanner. The LEDs and audible tones notify you of the curren

A-61662 October 2011 4-3Status The status area of the control panel consists of: Power Mode, Back Door, Maintenance and Manual Feed.Power Mode — thi

4-4 A-61662 October 2011 Maintenance — this yellow LED indicates that maintenance or service conditions exist in the scanner.Manual Feed — this gree

A-61662 October 2011 4-5Feeder table The Feeder Table adjustment buttons allow you to raise and lower the feeder table to accommodate different batc

4-6 A-61662 October 2011 Multifeed — when illuminated, indicates multiple or overlapped documents have been detected entering the scanner. This indi

A-61662 October 2011 4-7Batch Control The Batch Control buttons allow you to restart and stop scanning.Ready — this indicator is illuminated green w

4-8 A-61662 October 2011 Ngenuity Batch CounterThe Ngenuity Batch Counter application can be started from Start>Programs>Kodak>Ngenuity 900

A-61662 October 2011 4-9Ngenuity Operator Utility main screenThe Ngenuity Operator Utility main screen provides a menu bar and options for configuri

Environmental information•The Kodak Ngenutiy Scanners are designed to meet worldwide environmental requirements.• Guidelines are available for the dis

4-10 A-61662 October 2011 Menu barScanner menu Details — displays a Scanner Details dialog box which contains version information for scanner firmwa

A-61662 October 2011 4-11Feature Access Feature Access provides a way of allowing full, limited or view-only access to the features available in the

4-12 A-61662 October 2011 3. Select the option that you want to configure and click Next.• Select feature availability — allows you to set the follo

A-61662 October 2011 4-13Home screen When you click the Home button on the main Ngenuity Operator Utility screen, the following information is displ

4-14 A-61662 October 2011 Scanner Self Test — displays the results of the internal scanner fault monitoring. A green checkmark icon indicates that n

A-61662 October 2011 4-15Resetting the maintenance remindersIf a maintenance interval expires triggering the maintenance reminder, a hyperlink for t

4-16 A-61662 October 2011 Custom Functions — allows you to set a function for the F1 and F2 buttons on the control panel. Available options are:• No

A-61662 October 2011 4-17Advanced settings • Select the Advanced button on the Configure Scanner Settings screen to access additional scanner settin

4-18 A-61662 October 2011 Configuration tab: allows you to configure advanced scanner features. Front Panel MF Ignore Button Mode — allows you to se

A-61662 October 2011 4-19Maintenance button When you click the Maintenance button on the Ngenuity Operator Utility main screen, the Maintenance scre

Peoples Republic of ChinaWARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the use

A-61662 October 2011 5-1 5 Advanced FeaturesContents Accessing Advanced features...5-2Advanced

5-2 A-61662 October 2011 Accessing Advanced featuresTo access the VRS Interactive Viewer, Ngenuity VRS Professional software must be loaded on the ho

A-61662 October 2011 5-3Advanced Properties dialog boxThe features on the Advanced Properties dialog box can be used to control scanner-specific fea

5-4 A-61662 October 2011 Color screen The Color screen allows you to dropout a form's background so that only the entered data is included in th

A-61662 October 2011 5-5Picking Rectangle screen The Picking Rectangle screen provides the following options:Front Side/Back Side — allows you to de

5-6 A-61662 October 2011 Rotation screen The Rotation screen provides the following options.Front Side/Back Side — allows you to rotate the scanned i

A-61662 October 2011 5-7Toggle Color Mode screen The Toggle Color Mode screen provides the following features.Preferences• Use patch code detection

5-8 A-61662 October 2011 Document Setup screen The Document Setup screen provides the following options.Document Types — allows you to change the tra

A-61662 October 2011 5-9Following is a table that identifies those other controls as well as how the scanner and software handle the conflict when y

5-10 A-61662 October 2011 Advanced Color screen The Advanced Color screen provides the following options. If the color on your images is not as expec

OVERVIEW 1-1INSTALLATION 2-1GETTING STARTED 3-1CONTROL PANEL AND NGENUITY OPERATOR UTILITY 4-1ADVANCED FEATURES 5-1MAINTENANCE 6-1TROUBLESHOOTING 7

A-61662 October 2011 5-11Gamma (default) — allows you to specify a specific camera gamma (1.0 - 2.5). The camera gamma value can be entered or selec

5-12 A-61662 October 2011 • Stop: when a multifeed is detected, the scanner sounds an audible alarm, the Multifeed LED lights steady and the scanner’

A-61662 October 2011 5-13About screen The About screen displays the scanner version and copyright information.

A-61662 October 2011 6-16 MaintenanceContents Maintenance schedule ...6-2Cleaning su

6-2 A-61662 October 2011 Maintenance scheduleThe following table is a recommended schedule for performing basic maintenance functions. Some procedure

A-61662 October 2011 6-3Cleaning procedures Cleaning your scanner and performing preventative maintenance on a regular basis is required to ensure t

6-4 A-61662 October 2011 Cleaning the feed rollers Feed rollers include the pick roller, drive roller and separation roller.All feed rollers should b

A-61662 October 2011 6-55. Re-install the pick roller.6. Remove the drive roller by pushing the roller to the right. Hold the drive roller shaft in

6-6 A-61662 October 2011 12. Close the scanner cover and reset the maintenance reminder by clicking on the Clean Feed Rollers link on the Maintenance

A-61662 October 2011 6-7Cleaning the optics Optics include the imaging guides, camera glass covers and sensors. All of the optics components should

A-61662 October 2011 1-1 1 OverviewContents Supporting documentation...1-1Optional access

6-8 A-61662 October 2011 4. With the imaging guide still out of the scanner, locate the glass camera cover between and below the LED lamps.5. Using a

A-61662 October 2011 6-9Cleaning the sensorsThere are 7 sensors that require regular cleaning. Use only the supplied blower brush to clean these sen

6-10 A-61662 October 2011 11. Exit sensor: The exit sensor is located on the transport toward the back of the scanner. Clean the exit sensor by placi

A-61662 October 2011 6-11Cleaning the transport Over time, the transport will become dirty and may feed documents erratically or skew the documents

6-12 A-61662 October 2011 Replacement proceduresThis section provides procedures for replacing the following parts: the feed rollers, the pre-separat

A-61662 October 2011 6-13Replacing the pre-separation padChange the pre-separation pad when the frequency of multi-fed documents increases.1. Open t

6-14 A-61662 October 2011 Camera calibration Camera calibration is important for maintaining consistent image quality and should be performed periodi

A-61662 October 2011 6-154. Lift the skimmer and make sure the feeder tray is empty. The scanner will automatically go into Manual Feed Mode, the fe

6-16 A-61662 October 2011 Supplies and consumables Contact your scanner supplier to order supplies. NOTE: Items and catalog numbers are subject to ch

A-61662 October 2011 7-17 TroubleshootingContents Clearing a document jam...7-1Problem

1-2 A-61662 October 2011 Optional accessories Front/Rear Printer Kit — front page (pre-scan) and back page (post-scan) imprinting prints user-specif

7-2 A-61662 October 2011Problem solving Occasionally you may encounter a situation with your scanner where it may not function properly. Use the cha

A-61662 October 2011 7-3CGA Port Not Responding ... Cycle power to the scanner. If the problem persists, contact Technical Support.Corrupt or Missin

7-4 A-61662 October 2011Contacting Service 1. Visit www.Kodak.com/go/dicontacts to obtain the most current phone number for your country.2. When cal

A-61662 October 2011 A-1Appendix A SpecificationsContents Specifications...

A-2 A-61662 October 2011 System requirements Following is the minimum recommended system configuration to run Kodak Ngenuity 9000 Series Scanners:Re

A-61662 October 2011 B-1 Appendix B Installing and Using the ImprinterContents Installing the front page imprinter and ink cartridge...

B-2 A-61662 October 2011 The imprinter is controlled from the scanning application installed on the host PC.Installing the front page imprinter and i

A-61662 October 2011 B-33. Move the carriage to the center position.4. Hold the ink cartridge holder with one hand and place the ink cartridge (bott

B-4 A-61662 October 2011 10. Connect the imprinter cable to the connector on the imprinter unit noting the orientation of the key on the plug and the

A-61662 October 2011 B-5Installing the back page imprinter and ink cartridgeTo ensure proper installation of the ink cartridge, install the imprinte

A-61662 October 2011 1-3Scanner componentsFront view1 Control Panel — allows you to initiate scanner functions directly from the scanner.2 Feeder ta

B-6 A-61662 October 2011 9. Connect the imprinter cable noting the orientation of the key on the plug and the slot on the connector.10. Close the bac

A-61662 October 2011 B-7MaintenanceReplacing the ink cartridge 1. Turn off the scanner and power down the host PC.2. Remove the front (or back) imp

B-8 A-61662 October 2011 Cleaning the ink cartridge print headIf the print head of the ink cartridge is dirty or the ink cartridge has not been used

A-61662 October 2011 B-9Additional print head cleaningIf cleaning the print head using the F1 key does not provide the desired results, you can furt

B-10 A-61662 October 2011 Using the imprinter Imprinter operation is controlled via the hardware and software.Print position: hardware To print a str

A-61662 October 2011 B-11Print position: software To set up the software for imprinting, access the Advanced Properties screen which is accessible w

B-12 A-61662 October 2011 The following options can be set via the Text Controls dialog box:NOTE: Patch Code functionality is only available with the

A-61662 October 2011 B-13• Digits — select a value from the drop-down list to specify the page counter length, which should take into consideration

B-14 A-61662 October 2011 Special Content — select special content format codes to include in the text string from the drop-down list. These codes ar

A-61662 October 2011 B-15• Offset from Top — specify the distance of the imprinter string from the top of each page. The default and minimum value i

1-4 A-61662 October 2011 6 Separator roller door — allows access to the separator roller. The separator roller assists in separating documents as th

B-16 A-61662 October 2011 Patch Code options Imprint Patch Code Sheets — enable this option if you want to print on patch code sheets and count them

A-61662 October 2011 C-1Appendix C Installing and Using the Optional Straight Pass- Through AdapterContents Installing the straight pass-through adap

C-2 A-61662 October 2011Using the straight pass-through adapterNOTE:If you are scanning exception documents, it is not necessary to have the exit tra

A-61662 October 2011 D-1Appendix D GlossaryControl panel — interface located on the front of the scanner that is used to perform basic scanning funct

A-61662 October 2011 E-1Appendix E Patch Code InformationThis appendix provides additional information for patch codes supported by Kodak Ngenuity 90

E2 A-61662 October 2011The horizontal placement must result in the patch pattern crossing the scanner’s sensor locations. Refer to the following illu

A-61662 October 2011 E-3Key for Graphical Pattern Description:W Wide Barn Narrow BarThe graphical pattern read from left to right indicates the time

E4 A-61662 October 2011Patch codesPatch 7 Patch 8Patch 9Patch 10Patch 11Patch 12Patch 13Patch 14